Hoses & connectors: $100–$200
The brittle old flexible behind the cooktop: tiny part, outsized share of the leaks we find.
Licensed Gas Fitting
Gas Work Done
Properly Across
Pymble
Gas is the one trade where "pretty confident" is not a standard. Leaks found and repaired, cooktops and heaters connected, lines run and certified: all of it by licensed gasfitters, all of it pressure-tested before the gas goes back on in Pymble.
- Licence 368473C, fully insured
- Manometer-tested to AS/NZS 5601, every job
- Gas smell right now? 131 909 before anything
Why Gas Work Is Licensed Work In Pymble
NSW reserves every gas task, down to connecting an oven, for licensed gasfitters, and the logic is unsentimental: plumbing mistakes stain ceilings, gas mistakes burn houses and poison air. The leaks we attend have a recurring origin story, and it is rarely the pipework’s idea, it is a confident DIY connection or a handyman’s thread tape, discovered later by someone’s nose.
What the licence actually buys is the ending: the whole installation held against a manometer until the needle refuses to move, every appliance checked for a clean blue burn and honest ventilation, and the work done to AS/NZS 5601, the clause your insurer reaches for when something ever goes wrong. Across Pymble and the Upper North Shore, no gas job of ours skips that ending.
LPG: a different system with different rules
Homes set well back from the road run lengthy drains that trap debris and are slow to clear without proper jetting gear.
Beyond the reticulated network, gas means bottles or a bulk tank. LPG runs at a different pressure from natural gas, uses different jets and regulators, and appliances are not interchangeable between the two without conversion.
It is the single most common mistake we correct on rural properties: a natural gas appliance bought secondhand and connected to LPG. It will burn, badly and unsafely, and the yellow flame is the giveaway.
Gas that arrived long after the house did
Early-1900s homes still run original earthenware sewers that crack and sag with age, snagging waste and backing up.
A period home was not built with gas in mind. Whatever it has was added later, often several times, and the runs take whatever route was available at the time, under floors, through cavities, along the outside of a wall and back in.
Which is why the first job on an older property is usually establishing what is actually there. A pressure test tells you whether the installation is sound; it does not tell you where it goes, and both matter before anything is added.
Bottle and tank installations
Cylinder and bulk tank installations have clearance requirements from boundaries, openings, ignition sources and vehicle paths, and those are the things most often wrong on a property where a shed or deck has been added since.
Sizing is the quiet failure. Adding an appliance to a line that was adequate for the original load can starve everything else on it, so we check what the existing run can actually carry before extending it.
It is worth a check whenever anything is built near an existing installation. A compliant tank position can become non-compliant because something was built beside it, and that surfaces at sale time if not before.
Why gas work is licence-only, without exception
Gasfitting is licensed work in NSW and there is no handyman tier of it. It is not bureaucratic caution, unburnt gas and incorrectly burnt gas are both lethal, and the second one is odourless.
It also has consequences beyond safety. Unlicensed gas work voids home insurance, invalidates appliance warranties, and surfaces during a sale. Every job here is done under licence and finishes with a certificate.
Selling, buying or leasing a property
Gas installations surface at transaction time. Buyers' inspections flag uncapped lines and old unflued heaters, insurers ask about compliance, and commercial leases usually require current certification.
A test before listing is cheap and removes a negotiating point. If you are buying an older property, having the gas installation tested before settlement is one of the better-value inspections available.
What a blue flame is telling you
Correct combustion is blue and steady. Yellow, lazy or lifting flames mean the air-to-gas ratio is wrong, a blocked jet, a starved supply, insufficient ventilation, or an appliance set up for a different gas type.
It is the one diagnostic anyone can do without equipment, and it is worth a look at every gas appliance in the house once a year.
What it costs in Pymble
Joints & fittings, $200–$600
Thread and valve leaks sealed properly and proven again on the gauge.
Pipe runs, $400–$1,500
Corroded or damaged sections replaced; concealed lines with access work run $800–$2,500.
Appliance connections, from ~$200
Connected, tested, certified. New line or bayonet to reach it quoted fixed on top.
The market rate, $120–$220/hr
Sydney's 2026 licensed-gasfitter range; attendance typically $80–$150. Certification is included, because without it there is no job.
Every gas job ends with a pressure test and the paperwork that proves it. Figures here are indicative of the 2026 Sydney market rather than a quote from us, you get your own number as a fixed price before any work starts.
A Gas Job, Properly Ordered
Step 01
Step 01
Isolate Before Anything
Suspected leaks start with the supply off at the meter and air moving through the space. Diagnosis begins only after the installation stops feeding the problem.
Step 02
Let The Gauge Accuse
A manometer says whether the system is losing gas; detection fluid and instruments then walk the installation to the guilty joint, fitting or run.
Step 03
Replace, Never Bodge
The failed component comes out and compliant material goes in, to AS/NZS 5601, whether that is one connector or metres of rerun line.
Step 04
Prove, Relight, Certify
The full installation holds on the gauge or we are not done. Appliances relit, flames checked blue, ventilation confirmed, compliance documented.
New Appliance Still In Its Box?
Nor should it, legally. One visit: connected, tested, certified, warranty intact. The proper way is also the cheap way, counted honestly.
The installation is isolated, brought to a set pressure and watched on a manometer for a defined period. If the needle holds, the system is tight; if it drops, gas is escaping and the test indicates roughly how much. It is the only way to know the condition of pipework you cannot see.
Leave the building and take everyone with you. No light switches, no appliances, no phone calls made inside: a switch operating is an ignition source. From outside, ring 131 909, the gas network's emergency line, staffed around the clock. They attend and make the supply safe at no cost to you.
Indicatively: a pressure test and leak location $220-$450; a new bayonet or appliance point $350-$800 depending on the run; an appliance service $180-$320; a cooktop changeover $250-$500 where the point already exists. Market figures for 2026, not a quote, and every job includes the compliance certificate rather than adding it.
Yes, and it matters. LPG runs at a different pressure with different jets, and appliances are not interchangeable without conversion. The most common mistake we correct on rural properties is a natural gas appliance bought secondhand and connected to LPG, it will burn, badly and unsafely, and the yellow flame gives it away.
It can be, and testing is the only way to know. A period home was not built with gas in mind, whatever it has was added later, often several times, taking whatever route was available. The first job is usually establishing what is actually there before anything is added to it.
Clearances from boundaries, openings, ignition sources and vehicle paths. Those are what most often go wrong on a property where a shed or deck has been added since, a compliant tank position can become non-compliant because something was built beside it. It surfaces at sale time if not before.
Not necessarily. Redundant pipework from a disconnected heater, a removed stove or a converted fireplace is not always capped to any standard, or capped at all. It is the single most common reason an old house fails a pressure test, and usually inexpensive to put right once located.
Get The Gas Done Properly In Pymble
Licensed hands, a passing pressure test, and the certificate to prove it. Smelling gas this minute? 131 909 from outside comes before this form.
